/*
 * BlinkMChuck -- Control a BlinkM with a Wii Nunchuck
 *
 *
 * BlinkM connections to Arduino
 * PWR - -- gnd -- black -- Gnd
 * PWR + -- +5V -- red   -- 5V
 * I2C d -- SDA -- green -- Analog In 4
 * I2C c -- SCK -- blue  -- Analog In 5
 *
 * Note: This sketch resets the I2C address of the BlinkM.
 *       If you don't want this behavior, comment out "BlinkM_setAddress()"
 *       in setup() and change the variable "blink_addr" to your BlinkM's addr.
 *
 * 2008 Tod E. Kurt, http://thingm.com/
 *
 */

#include "Wire.h"
#include "BlinkM_funcs.h"
#include "nunchuck_funcs.h"

int blinkm_addr = 0x10; // the address we're going to set the BlinkM to
int loop_cnt=0;

float hue, bri;
byte zbut,cbut;
byte fadetoggle;
byte fast_fade = 30, slow_fade = 5;
int ledPin = 13;

#define BLINKM_ARDUINO_POWERED 1

void setup()
{
    Serial.begin(19200);
    
    if( BLINKM_ARDUINO_POWERED ) {
        BlinkM_beginWithPower();
    } else {
        BlinkM_begin();
    }

    BlinkM_setAddress( blinkm_addr );  // comment out to not set address
    
    byte rc = BlinkM_checkAddress( blinkm_addr );
    if( rc == -1 ) 
        Serial.println("\r\nno response");
    else if( rc == 1 ) 
        Serial.println("\r\naddr mismatch");
    
    BlinkM_stopScript(blinkm_addr);  // in case there is a startup script
    BlinkM_setFadeSpeed(blinkm_addr, slow_fade); 

    nunchuck_init(); // send the initilization handshake
    
    if( rc == 0 )
        Serial.print("BlinkMChuck ready\n");
    else 
        Serial.print("BlinkMChuck error initializing\n");

}

void loop()
{
    if( loop_cnt > 100 ) { // every 100 msecs get new data
        loop_cnt = 0;

        nunchuck_get_data();

        hue  = nunchuck_accelx(); // ranges from approx 70 - 182
        bri  = nunchuck_accely(); // ranges from approx 65 - 173
        zbut = nunchuck_zbutton();
        cbut = nunchuck_cbutton(); 

        // C buton toggles fast or slow fading
        if( cbut ) {
            BlinkM_setFadeSpeed(blinkm_addr, (fadetoggle)?fast_fade:slow_fade);
            fadetoggle = !fadetoggle;
            digitalWrite(ledPin, fadetoggle);
        }

        // Z button fades to black
        if( zbut ) {
            BlinkM_fadeToHSB( blinkm_addr, hue, 0xff, 0); // fade to black
        } else {
            // massage a bit to get more range
            hue = (hue-70) * 2.2;  // empirically determined
            bri = (bri-60) * 2.2;  // empirically determined
            
            Serial.print("hue: "); Serial.print((byte)hue,DEC);
            Serial.print("\tbri: "); Serial.println((byte)bri,DEC);
            
            // set blinkm color
            BlinkM_fadeToHSB( blinkm_addr, hue, 0xff, bri );
        }

    }
    loop_cnt++;
    delay(1);
}